What Makes a Whirlpool Front Load Washer Leak?

All washing machines are prone to failure over time.

Like all major appliances, the Whirlpool Duet front-loading washer is prone to failure over time. Some of these failures may result in either a minor or a major leak which typically can be fixed by any handyman or even yourself.

1. Hoses

   • Hoses, commonly made of rubber, are typically the first parts to fail on a washing machine. If your Whirlpool Duet is leaking, it is best to check the hoses first. There are three hoses of major concern: the main drain hose and separate cold and hot water hoses. Ensure all hoses are free of kinks or holes, and ensure all are attached properly to both the washing machine and the main water valve in your home. If you find a problem, replace the hose promptly.
   
   

   Drain Pump

   • Part # 280187. Complete Pump Assembly (comes with hoses!) All washing machines, including the Whirlpool Duet, rely on an inner pump to regulate the water level. If your Whirlpool Duet is leaking, especially when the machine’s main basket is filled with water, the pump could be to blame. Two hoses are connected to the pump, which should be checked for any holes or kinks. These can easily be replaced if faulty, but the whole pump unit may require replacement if the hoses appear to be in working order.
   
   

   Tub

   • Whirlpool Part # W10269756. The plastic outer tub of your Whirlpool Duet washing machine may erode, rust or otherwise develop a hole or crack.  Additionally, the rubber seal located between the machine’s transmission and its plastic outer tub may also be responsible for a leak. To detect a leak of this type, fill your washing machine with water and a small amount of laundry detergent. The leak should be apparent underneath the outer tub.
   
   

   Water Inlet Valve

   • Part # 8181694. The water inlet spout is a small plastic part located within the machine’s main basket. If your Whirlpool Duet washer is leaking, ensure that this piece is fully attached to the machine and free of any cracks or damage. If a problem is found, the spout should be replaced promptly.
     
     Bellow
   •  Whirlpool Part # 8181850.  This Whirlpool Bellow is also known as a Boot Seal and is used in front load washers to fix leaking water. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle

These parts can be used in the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Kenmore, Admiral, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

Read more: What Causes a Whirlpool Duet Washer to Leak? | eHow.com http://www.ehow.com/info_12117241_causes-whirlpool-duet-washer-leak.html#ixzz25c80mpmd

Reasons to Replace the Tub In a Whirlpool Washer

If you have noticed leaking water under your washer or even foul odors in washed clothes, it may be time to take a look at the tub. Years of use can build up sediment around a tub. This will not only start to create foul odors but can also lead to tub corrosion. The average person can remove the tub in a Whirlpool washer. The tub can be thoroughly cleaned and inspected for damage after removal from the washer.

We carry the COMPLETE TUB – Whirlpool Part # W10269756.

Includes:

Outer Tub – Whirlpool Part # W10253866
Tub Gasket – Whirlpool Part # 8181673
Stainless Steel Basket – Whirlpool Part # W10269756
Counterweight – Whirlpool Part # W10008880
Rear Counterweight – Whirlpool Part # 8181644

This part also works with the following brands: Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Kenmore, Admiral, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

Contact parts@laundrypartsmarket.com for more details.

Things You’ll Need

• Phillips-head screwdriver
• Flathead screwdriver
• Socket wrench set

Instructions

1. • Disconnect the Whirlpool washer power cord from the wall outlet. Move the washer away from the wall so the control console can be placed into the service position without damaging the wall.
     
   • 2
     Unscrew the retaining screws on the front end of the control console that secure the console to the top of the washer with a Phillips-head screwdriver. Lift the front of the control console and set it back on its hinges to place the console in the service position.
     
   • 3
     Disconnect the two brass holding clips on the top corner of the washer by inserting a flathead screwdriver into the clip and prying the clip out. The brass clips secure the rear panel to the top of the washer. Unplug the lid switch connector on the top rear of the washer. Press in on the single locking tab and pull the connector apart. Lift the washer cabinet off of the washer base and out of your way.
     
   • 4
     Remove the fabric softener from the top of the agitator by pulling it straight off with your hand. There is a debris cap inside the agitator. Remove the debris cap by grabbing the handle and lifting it out of the agitator. Use a socket wrench to remove the agitator bolt from the center of the agitator. Grab the bottom of the agitator and lift it straight out of the tub.
     
   • 5
     Unsnap the eight tab clips that secure the upper tub ring around the outside tub. It may be necessary to use a flathead screwdriver to pry the clips apart. Lift the tub ring off of the washer tub.
     
   • 6
     Use a spanner wrench to loosen the spanner nut on the spin tube inside the washer tub and inner basket. Insert a large flathead screwdriver into the spanner block and twist the handle to expand the spanner block. Lift the inner basket out of the outer tub.
     
   • 7
     Compress the compression clamp on the hose connected to the side of the outer tub and pull the hose off of the tub with a pair of pliers. Locate the three areas that the tub attaches to the tub support. There is a spring, locating tab and two screws at each location. Disconnect these three areas and lift the tub away from the washer.
     

Read more: How to Remove the Tub in a Whirlpool Washer | eHow.com http://www.ehow.com/how_5633400_remove-tub-whirlpool-washer.html#ixzz25c2s3glX